谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 公司動態 >

卷簾門電機的運用方法

發布人:http://www.levels4life.com    發布時間:2017-02-20 11:49:28

卷簾門電機如何正確的運用,下麵由濟南卷簾門廠家的小編為您介紹一下:
How to use the rolling door motor, the following by the Ji'nan rolling shutter door manufacturers to introduce you:
1、電機工作環境應保持幹燥,電動機外表應保持清潔,進風口不應受塵土、纖維等阻止。
1, the motor working environment should be kept dry, motor appearance should be kept clean, air inlet should not be dust, fiber, etc..

20161214750871.jpg2、當電動機的熱保護接連發作動作時,應查明問題來自電動機的超負荷運行或熱保護設備設定值太低,消除故障後,方可投入運轉。
2, when the motor thermal protection after a series of attacks, the problem should be identified from the overload operation of the motor or thermal protection equipment set value is too low, to eliminate the fault before they can be put into operation.
3、應保證電動機在運轉的潤滑,即應彌補或替換 光滑脂運轉中發現軸承過熱或光滑蛻變時,液壓 及時換光滑脂。替換光滑脂時,應鏟除舊的光滑油,並有汽油洗淨軸承及軸承蓋的油槽,然後將 ZL-3鋰基脂 填充軸承內外圈之間的空腔的 1/2 對 2 極(及 2/3 對4 6 8 極)。
3, should ensure that the motor in the operation of lubrication, that should be made up or replace the smooth operation of the grease found bearing overheating or smooth disintegration, hydraulic timely for smooth grease. Replace the grease, oil should be the eradication of the old, and the oil tank of gasoline to clean the bearing and bearing cover, and then the ZL-3 lithium grease filled cavity between the inner and outer rings of the bearing of the 1/2 on the 2 (and 2/3 468 pole).
4、當軸承的壽命終了時,電動機運轉的振蕩及噪聲將顯著增大,查看軸承的徑向遊隙抵達下列值時,即應替換軸承。
4, when the end of the life of the bearing, the vibration and noise of motor will be significantly increased, the radial clearance of the bearing in view the following values, which should replace the bearings.
5、設備電動機時,從軸伸端或非伸端取出轉子都能夠。若是沒有必要卸下電扇,仍是從非軸伸端取出轉子較為便當,從定子中抽出轉子時,應防止損壞定子繞組或絕緣。
5, when the motor equipment, from the shaft extension or non end rotor can be removed. If it is not necessary to remove the fan, or from the non shaft extending end out rotor is more convenient, from out of the rotor stator, stator winding insulation should prevent damage or.
6、替換繞組時有必要記下原繞組的辦法,尺度及匝數,線規等,當丟失了這些數據時,應向製作廠討取,隨意更改原描繪繞組,常常使電動機某項或幾項功用惡化,乃至於無法運用。
6, it is necessary to replace the winding down of the primary winding way, scale and number of turns of wire, etc., when the loss of the data, to get production plant, change the original picture often make the motor winding, one or several function deterioration, and cannot be used.

上一篇:防盜門選購需注意的要點
下一篇:談談大家對濟南車庫門的認識
產品中心
聯係向日葵视频app下载ioses网站免费