谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 公司動態 >

電動卷簾門如何安裝?

發布人:http://www.levels4life.com    發布時間:2019-01-17 14:51:32

卷簾門在很多超市和街邊的商鋪可以看到,包含了多管節活動的門片,將卷簾門片串聯片接在一起,緊密鎖定在特製的軌道中。因為安裝和操作方便,卷簾門也不斷進入普通用戶生活中,不僅小門洞可以安裝,一些門洞大的的車庫門,就可以安裝卷簾門上去。

  Curtain doors can be seen in many supermarkets and street stores, including multi-section movable doors, which connect the curtain doors in series and lock them tightly in a special track. Because of the convenience of installation and operation, rolling shutter doors are constantly entering the lives of ordinary users. Not only can small doors be installed, but also some garage doors with large doors can be installed on rolling shutter doors.

  卷簾門的安裝所需要的物件主要包括鋼製門框導軌、左右支架部件、門體上部金屬支架、手動或者電動門鎖等幾個部分,在安裝之前要先檢查門洞尺寸是否留有符合的空間安裝卷簾門門體要求,一般來說門上橫梁到頂板之間應該不小於500mm。在確定基本相關參數後,進行門體定位,並準備好電源連接、安裝具等。

  Installation of rolling shutter door mainly includes steel door frame guide rail, left and right bracket parts, upper metal bracket of door body, manual or electric door lock and other parts. Before installation, it is necessary to check whether the size of the door hole is left to meet the requirements of installation of rolling shutter door body. Generally speaking, between the upper beam and the top plate of the door should be no less than 500 mm. After determining the basic related parameters, the door body is positioned, and the power connection and installation equipment are prepared.

  街邊商鋪電動卷簾門

  Electric Curtain Door for Street Shop

  電動卷簾門鋼製導軌安裝步驟

  Installation Procedures of Electric Curtain Door Steel Guidance Rail

  1.首先用水平尺和墨線在門洞兩邊劃線定位;

  1. Firstly, the horizontal ruler and ink line are used to mark the position on both sides of the door.

  2.找到導軌在門洞上所對應的位置,做好標記並在相應的位置打孔,用膨脹螺栓打入固定點將側板固定在垂直線上,水平線是側板的高處;

  2. Find the corresponding position of the guide rail on the door hole, mark well and punch holes in the corresponding position, and fix the side plate on the vertical line with the expansion bolt into the fixed point. The horizontal line is the highest place of the side plate.

  3.用相同的方法安裝另一邊的鋼製導軌。

  3. Install the steelway on the other side in the same way.

  需要注意隻有導軌正麵和側麵豎直對應,安裝的時候要用垂直墜來確定導軌的垂直度,確定卷簾門的兩個鋼製導軌存在同一水平線上。

  It should be noted that only the front and side of the guide rail correspond vertically. Vertical drop should be used to determine the verticality of the guide rail and to determine that the two steel guide rails of the rolling curtain door exist on the same horizontal line.

20161214807515.jpg

  卷簾門電機的部位

  locations of motor for rolling shutter door

  卷簾門支架安裝

  Installation of curtain door bracket

  用水平尺定位好支架上端麵的平行線,支架外端點應該與導軌的側麵垂直。定好位置後,在牆壁上對應位置打孔,並用膨脹螺栓將其支架固定。用工具水平管引點,確定另一邊的支架位置,兩側邊上的支架所處在同一水平線上,可以利用水平管進行調試。隻有保證相同的水平線上時,卷簾門才能順暢地開關。

  The parallel line of the upper end face of the support should be positioned with a horizontal ruler, and the outer end point of the support should be perpendicular to the side of the guide rail. After fixing the position, drill holes in the corresponding position on the wall and fix the bracket with expansion bolt. The position of the bracket on the other side is determined by the horizontal pipe lead point of the tool. The bracket on both sides is located on the same horizontal line. The horizontal pipe can be used for debugging. Only when the same horizontal line is guaranteed, can the rolling shutter open smoothly.

  卷簾門門體安裝

  Installation of rolling shutter door body

  1.根據設計圖紙和現場的門洞寬度確定中軸長度,用人工或者機械將門體抬上支架。門體上支架前要注意門體運動的方向應該是從打開的前麵旋轉下來,方向正確才可以繼續;

  1. Determine the length of the mid-axis according to the design drawings and the width of the portal on site, and lift the portal body onto the bracket manually or mechanically. Before the bracket on the door body, attention should be paid to the direction of the movement of the door body should be rotated down from the front of the opening, so that the correct direction can continue.

  2.粗裝U形螺絲、鞍形鐵座和螺帽;

  2. Coarse U-shaped screw, saddle-shaped seat and nut;

  3.檢查門體在兩邊導軌的距離是否正確,確保不出現過來縫隙,如果確定軸心正好在門體卷心半徑位置後,就可以U形螺絲鎖緊;

  3. Check whether the distance between the doors on both sides of the guide rail is correct to ensure that there is no gap. If the axis is located exactly at the radius of the door roll, the U-shaped screw can be locked.

  4.將扭簧按順時針方向(有時候可能是反方向)向前扭緊一圈,扭緊後慢慢移動控製門體,將門體慢慢引入導軌內;

  4. Tighten the torsion spring forward in clockwise direction (sometimes in the opposite direction), then move the control door body slowly after tightening, and introduce the door body slowly into the guide rail.

  5.找到底軌的切口邊,在底軌上安裝限位塊;

  5. Find the cut edge of the bottom rail and install the limit block on the bottom rail.

  卷簾門安裝完以後要記得進行運行調試和安全檢查,上下開關門體多次,確保家用卷簾門運轉平穩、輕便。

  After the rolling shutter door is installed, it is necessary to remember to carry out operation debugging and safety inspection, and to switch the door body up and down many times to ensure that the rolling shutter door runs smoothly and lightly.

上一篇:電動卷簾門的安全問題解析!
下一篇:常規車庫卷簾門招標要求內容!
產品中心
聯係向日葵视频成年app下载安装