谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 公司動態 >

如何有效增加卷簾門的使用壽命?

發布人:http://www.levels4life.com    發布時間:2019-11-12 16:46:21

  快速百葉窗結構並不複雜,通常可以看到產品的概況通過肉眼觀察,主要觀察門的身體是否取消和關閉順利,如果不使用快速門很長一段時間最好的常規測試中,測試打開和關閉按鈕是否正常,電氣控製箱指示信號的情況。更詳細的保養可分為變頻器的保養、電機的保養、定期檢查變頻器進口是否有異物堵塞、每月清洗過濾器冷卻風道灰塵。年度檢查:導體和絕緣體沒有腐蝕,如有,應及時用酒精擦拭。

  The structure of the quick shutter is not complicated. Generally, you can see the general situation of the product through visual observation, mainly to observe whether the door body is cancelled and closed smoothly. If you do not use the quick door for a long time, in the best routine test, test whether the open and close buttons are normal, and the indication signals of the electrical control box. More detailed maintenance can be divided into converter maintenance, motor maintenance, regular inspection of converter inlet whether there is blockage of foreign matters, monthly cleaning of filter cooling air duct dust. Annual inspection: conductor and insulator are not corroded, if any, they should be wiped with alcohol in time.

  看看螺栓、螺釘和插件是否鬆動,有沒有對地短路和相阻的輸出和輸入電抗器,正常情況下應大於幾十兆歐。工業和石油汙染門上很難清潔,可以用清潔劑擦洗,最好不要使用強酸或堿清洗解決方案,這樣不僅容易使表麵光潔度受損,還可以破壞保護膜表麵的金屬碎片和氧化層,導致金屬件的腐蝕,尤其是當一些客戶的硫酸與牆麵清潔,必須注意不要讓門窗口的影響。工業門電機可以在適當的時候,做一次保養。

  Check whether the bolts, screws and plug-ins are loose, and whether there is output and input reactor with short circuit to ground and phase resistance, which should be greater than tens of megaohms under normal conditions. It is very difficult to clean industrial and oil polluted doors. You can scrub them with detergent. It is better not to use strong acid or alkali cleaning solutions. This will not only damage the surface finish, but also damage the metal chips and oxide layer on the surface of the protective film, resulting in the corrosion of metal parts. Especially when some customers clean the sulfuric acid and the wall, you must pay attention not to let the impact of doors and windows. The industrial door motor can be maintained at a proper time.

20161214578645.gif

  減速機至少每半年要加潤滑油,其他部件也要定期檢查,及時更換。在使用過程中,應盡量避免碰撞。對於工業門的扭力彈簧,使用一段時間後,如出現鬆動情況應及時調整緊,需要立即更換。打開工業門時,強度要適中,還要盡量保持打開和關閉時的速度。防火卷簾門旁邊安裝控製按鈕,當發生火災時,按下按鈕將快門按下。

  The reducer shall be lubricated at least every half a year, and other parts shall be inspected regularly and replaced in time. Collision shall be avoided as much as possible during use. For the torsion spring of industrial door, if it is loose after using for a period of time, it should be adjusted and tightened in time, and it needs to be replaced immediately. When opening the industrial door, the strength shall be moderate, and the speed of opening and closing shall be kept as far as possible. A control button is installed beside the fire shutter door. In case of fire, press the button to press the shutter.

  其次是火災報警係統的火災聯動控製,火災報警聯動控製係統與防火卷簾門控製器連接時,安裝防火卷簾門,火災報警聯動控製係統將信號反饋到防火卷簾門相應部位的電氣控製箱中,帶動卷簾門下降。這種控製方式是必須實現的控製方式,也是火災驗收的標準。最後,機械控製功能位於疏散走廊兩側的防火卷簾門應設置兩側的百葉窗啟閉裝置,也要求有機械控製功能,所以防火卷簾門應設置溫度保險絲控製裝置。

  The second is the fire linkage control of the fire alarm system. When the fire alarm linkage control system is connected with the fire shutter door controller, the fire shutter door is installed. The fire alarm linkage control system feeds back the signal to the electrical control box of the corresponding part of the fire shutter door to drive the shutter door down. This control mode is the control mode that must be realized, and it is also the standard of fire acceptance. Finally, the mechanical control function located on both sides of the evacuation corridor shall be equipped with shutter opening and closing devices on both sides, and also with mechanical control function, so the fire shutter door shall be equipped with temperature fuse control device.


上一篇:卷簾門電機控製器功率遠大於電機功率!
下一篇:上滑式車庫門的組成優勢!
產品中心
聯係向日葵app下载安装无限看