谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 公司動態 >

濟南車庫門鑰匙丟失怎麽辦?

發布人:http://www.levels4life.com    發布時間:2020-12-17 15:57:08

相信不少濟南車庫門的用戶有過遙控鑰匙丟失的情況,備用的鑰匙卻不多,遇到這種情況向日葵视频下免费下载應該如何對待呢?
I believe that many Jinan garage door users have lost the remote key, but there are not many spare keys. How should we deal with this situation?
首先當然是要重新配,但是在那裏配,這也是一個要注意的問題。
First of all, of course, it is necessary to re match them, but it is also a problem to pay attention to when matching there.
聯係廠家重新配車庫門的鑰匙是安全的辦法,但是效率相對比較慢。同時還可複製車庫門遙控器,自改碼,刪除丟失遙控器,消除安全隱患,但是部分用戶擔心遙控器的頻率問題,一直堅持要換頻率,可參照以下辦法:
Contacting the manufacturer to replace the key to the garage door is a safe way, but the efficiency is relatively slow. At the same time, it can also copy the remote control of garage door, change the code by itself, delete the lost remote control, and eliminate the potential safety hazard. However, some users are worried about the frequency of the remote control and insist on changing the frequency. Please refer to the following methods:
(1).清除遙控器的地址碼
(1) . clear the address code of the remote control
同時按住遙控器上方的兩個B C按鍵,這時LED閃亮一下後熄滅約2秒後LED快閃,這表明原來的地址碼已經清除了,這時短按所有按鍵LED都閃亮一下後熄滅。
At the same time, press and hold the two B C buttons on the top of the remote control, then the LED flashes once and then goes out. About 2 seconds later, the LED flashes quickly, which indicates that the original address code has been cleared. At this time, press all the buttons briefly, and the LED will flash once and then go out.

(2).複製其他遙控器的地址碼
(2) . copy the address code of other remote controls
將原配遙控器和學習遙控器靠近,同時按住需要複製的按鍵和學習型遙控器的一個按鍵,如果LED燈快速閃爍則說明這個按鍵的地址碼已經學習成功!遙控器上其他3個按鍵也用同樣的方法進行操作。
Close the original remote control to the learning remote control, and press and hold the key to be copied and a key of the learning remote control at the same time. If the LED light flashes quickly, it means that the address code of this key has been learned successfully. The other three keys on the remote control are operated in the same way.
那如果誤刪除地址碼怎麽辦?這個也是完全不用擔心的,隻要你同時按下遙控器下方的兩個D A按鍵約2秒後,LED開始快速閃爍,這說明被意外清除的地址碼已經被成功複原了。
What if you delete the address code by mistake? You don't have to worry about this. As long as you press the two Da buttons at the bottom of the remote control at the same time for about 2 seconds, the LED starts to flash quickly, which indicates that the address code that was accidentally cleared has been successfully restored.
上一篇:翻板車庫門在安裝過程中需要注意的問題
下一篇:車庫門的電源插座安裝位置注意事項
產品中心
聯係向日葵视频下免费下载