谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 行業新聞 >

電動卷簾門安裝的注意事項

發布人:http://www.levels4life.com    發布時間:2017-03-02 14:53:43

對於電動卷簾門,相信大家都不陌生,它被廣泛適用於商業門麵、車庫、商場、醫院、等公共場所或住宅,電動卷簾門不僅裝飾了人們的門麵,而且也為人們的使用提供了便利,那在安裝的時候,向日葵污视频下载應該注意什麽呢?下麵由濟南電動卷簾門廠家的小編為大家詳細介紹一下。
The electric shutter doors, I believe we are not unfamiliar, it is widely used in commercial window, garage, shopping malls, hospitals and other public places and residential, electric shutter doors not only decorate the people's appearance, but also provides convenience for people to use, that at the time of installation, we should pay attention to what the following? By the Ji'nan electric door manufacturers Xiaobian to introduce in detail.
1、卷門機必須按說明書要求安裝。
1, rolling door machine must be installed according to the specification requirements.
2、確定安裝水平線及垂直線,按設定尺寸依次安裝.槽口尺寸應準確,上下保持一致,對應槽口應在同一平麵內,然後用連接件與洞口內的預埋件焊牢。
2, install the horizontal line and the vertical line, according to the set sizes are installed. The slot size should be accurate, consistent, corresponding grooves shall be in the same plane, and then use the connecting piece and the hole in the welding parts.
3、寬大門體需在中間位置加裝中柱,兩邊有滑道.中柱安裝必須與地麵垂 直,安裝牢固,但要拆裝方便。
3, a door body in the middle position is in the column, a slide on both sides. In column must be installed perpendicular to the ground, firm installation, but easy disassembly.
4、安裝完略,先手動調自試運行,觀察門體上下運行情況,正常後通電調試。
4, install, starting dynamic adjusting and trial operation, observe the door body under normal operating conditions, after commissioning.

濟南電動卷簾門5、卷軸、文架板必須牢固地裝在混凝土結構上或預埋件上。
5, the scroll, frame plate must be firmly installed in the concrete structure or embedded parts.
6、調整製動器外殼方向,使環形鏈朝下;調整鏈條張緊度,鏈條6-10 mm;調整單向調節器及限位器。
6, adjust the direction of the brake shell, so that the chain down; adjust the chain tension, the chain 6-10 mm; adjust the one-way regulator and limit.
7、卷筒安裝應先找好尺寸,並使卷簡軸保持水平位置.注意與導軌之間的距離應兩端保將一致,臨時固定後進行檢查,並進行必要的調篷、校正,無誤後再與支架預埋件用電焊焊接。
7, the installation should first find a good size, and the volume or shaft to maintain the horizontal position. The distance between attention and guide should be guaranteed both ends will be consistent, temporary fixation after the inspection, and make necessary corrections, awning, correct with embedded parts by welding welding bracket.
8、清理,粉刷或鑲砌導軌牆體裝飾麵層,清理現場。
8, cleaning, painting or inlay guide wall decorative surface, clean up the scene.

上一篇:高速卷簾門設備的使用說明
下一篇:如何選擇車間自動車庫門
產品中心
聯係向日葵视频app下载ioses网站免费