谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 行業新聞 >

電動卷簾門給你不一樣的體驗

發布人:http://www.levels4life.com    發布時間:2017-03-28 16:57:04

  向日葵污视频下载都清楚電動卷簾門應用極為廣泛,不僅操作方便,而且造型越來越美觀,這是消費者選擇的主要原因。不過,在使用過程中會遇到一些故障,濟南卷簾門給大家講述下怎樣解決電動卷簾門故障。
We all know that electric shutter application is very wide, not only easy to operate, and more and more beautiful modelling, this is the main reason for consumers to choose. In use process, however, will have some trouble, under the jinan electric rolling door to talk about how to solve electric shutter fault.
  一、電動機不動或轉速慢此故障原因一般是線路斷路、電機燒損、停止按鈕沒複位、限位開關動作、負載較大等引起。
Fixed or an, motor speed slow this is the cause of the problem in the general line open circuit, motor loss, stop button didn't reset, limit switch action, larger load, etc.
  處理方法:檢查線路、並接通;更換燒損電機;更換按鈕或重複按動幾次; 撥動限位開關滑塊使它脫離微動開關觸點, 並調整微動開關位置;檢查機械部分 有無卡阻,若有則消除卡阻清理障礙物。
Processing method: check the line, and connected; Replace the burning motor; Replace the repeat push button or several times; Limit switches slider to make it out of the micro switch contact, and adjust the micro switch position; Check whether there is any jam on mechanical parts, if there is eliminate jam clear obstacles.
  二、控製失效故障發生的部位及原因:繼電器觸點粘死、行程微動開關失效 或觸片變形、滑塊緊定螺釘鬆、靠板螺絲鬆使靠板移位,使滑塊或螺母不能隨絲 杆轉動而移動、限位器傳動齒輪破損、按鈕上、下鍵卡死。
Second, the control part and the reasons of the failure happened: relay contact stick to death, micro switch failure Or contact deformation, the slider tight set screw loose, by plate screws that by displacement of plate, the slider or nut can't move with screw rotation, stop driving gear damage, button, the key card to death.
  處理方法:更換繼電器;更換微動開關或觸片;緊定滑塊螺釘並 使靠板複位;更換限位器傳動齒輪;更換按鈕。

濟南卷簾門Processing method: change the relay; Change the micro switch or touch; Set the slider screw and to reset the on board; Replace the stop transmission gear; Change the button.
  三、手拉鏈不動,故障原因:環形鏈條堵住十字槽;棘爪無脫離棘輪;壓鏈架卡死。
Three, hand zipper, the cause of the problem: circular chain block cross slot; Ratchet without out of ratchet; Chain frame jammed.
  處理方法:理順環形鏈條;調整棘爪與壓鏈架相對位置;更換或潤滑銷軸。
Processing method: smooth circular chain; Adjust the pawl and chain frame position; Replace or lubrication pin.
  四、電機振動或噪聲較大,故障原因:刹車盤不平衡或斷裂;刹車盤無緊固;軸承失油或失效;齒輪齧合不順、失油或磨損嚴重;電機電流聲或振動。
Four, motor vibration or noise is bigger, the cause of the problem: the brake disc imbalance or fracture; Brake disc without fastening; Bearing oil loss or failure; Gear mesh, serious loss of oil or wear; Electrical mechanical and electrical LiuSheng or vibration.
  處理方法:更換刹車盤或重新調整平衡;緊固刹車盤螺母;更換軸承;修配電機軸輸出端齒輪、潤滑或更換;檢查電機,如電機壞損則更換。
Methods: replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace the bearing; And replacement motor shaft output gear, lubrication or replacement; Check the motor, such as motor bad loss is replaced.
  向日葵视频app下载ioses网站免费以優良的產品,完美的服務,可靠的信譽,為您的事業成功助一臂之力,竭誠歡迎各界同仁惠顧洽談業務!
With our excellent products, perfect service, reliable credit, for your career success help, sincerely welcome all circles to patronize negotiate business!

上一篇:遙控車庫門的故障和處理方法
下一篇:電動卷簾門的優勢
產品中心
聯係向日葵污视频下载