谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 行業新聞 >

工業門不同提升方式彈簧的安裝方法!

發布人:http://www.levels4life.com    發布時間:2020-01-07 15:13:32

  工業門的吊裝方式分為上滑吊裝、完全垂直吊裝和半垂直吊裝三種。扭轉彈簧的安裝如下。

  The hoisting methods of industrial doors are divided into three types: up sliding hoisting, full vertical hoisting and semi vertical hoisting. The torsion spring is installed as follows.

  一、滑升式工業門:

  1、 Sliding industrial door:

  1. 將門體置於下(即處於關閉狀態):將扭簧一端固定,將扭簧另一端纏繞安裝所需的匝數,然後將扭簧調整端推至固定端,擰緊調整法蘭上的螺絲。扭力彈簧繞組數=門高÷線輪周長+預緊0.5 ~ 1圈。

  1. Put the door body down (i.e. in the closed state): fix one end of the torsion spring, wind the other end of the torsion spring around the number of turns required for installation, then push the adjusting end of the torsion spring to the fixed end, and tighten the screws on the adjusting flange. Number of torsion spring windings = door height ÷ circumference of wire wheel + pre tightening 0.5 ~ 1 turn.

  2. 將門體置於頂部(即開啟狀態):將扭力彈簧一端固定,將扭力彈簧沿調節端延長60 ~ 120mm,預緊0.5 ~ 1圈,最後將扭力彈簧的調節端用螺絲固定在軸上。為什麽要拉伸扭力彈簧?因為在提升門體的過程中,扭轉彈簧的外徑會變小,轉動次數會增加,因此,彈簧的伸長使其有一定的間隙,便於提升門體。

  2. Place the door body at the top (i.e. open state): fix one end of the torsion spring, extend the torsion spring along the adjusting end by 60 ~ 120mm, pre tighten by 0.5 ~ 1 turn, and finally fix the adjusting end of the torsion spring on the shaft with screws. Why do you want to stretch the torsion spring? Because in the process of lifting the door body, the outer diameter of the torsion spring will be smaller, and the number of turns will increase. Therefore, the extension of the spring makes it have a certain gap, which is convenient for lifting the door body.

20161214103489.jpg

  2、完全垂直提升工業門:因為扭力彈簧總是軸承門的重量均勻的身體,隻有通過改變砂輪直徑的大小,也就是說,改變轉矩的大小,為了使扭力彈簧和門實現平衡,所以你需要安裝塔輪。全立式提升工業門扭力彈簧安裝需預緊。鋼絲繩的長度必須根據塔輪的鐵絲板來確定。當門體向頂部打開時,鋼索從塔輪上的大圓繞到小圓。

  2. Fully vertical lifting industrial door: because the torsion spring is always the body with even weight of bearing door, only by changing the diameter of grinding wheel, that is to say, changing the torque, in order to balance the torsion spring and door, you need to install tower wheel. The torsion spring installation of the vertical industrial door needs to be pre tightened. The length of the wire rope must be determined according to the wire board of the tower wheel. When the door body is opened to the top, the wire rope goes from the big circle on the tower wheel to the small circle.

  三、半立式提升工業門:需要安裝半塔輪使扭力彈簧扭矩與門重新平衡。半塔輪的塔輪部分用於門的垂直升降。門的滑動部分與半塔輪的平麵部分一起提升。

  3、 Semi vertical lifting industrial door: it is necessary to install a half tower wheel to rebalance the torque of torsion spring with the door. The tower wheel part of the half tower wheel is used for the vertical lifting of the door. The sliding part of the door is lifted together with the plane part of the half tower wheel.

  半立式提升工業門的扭力彈簧在安裝時也需要預緊。鋼絲繩纏繞方法是:首先從半塔的大圓輪小圓,和充滿,然後繼續循環半塔平輪的輪,平輪上的匝數根據舉升高度的滑動門上一部分的身體來確定。

  The torsion spring of the semi vertical lifting industrial door also needs to be pre tightened during installation. The winding method of steel wire rope is as follows: firstly, from the big round wheel of the half tower to the small circle, and then continue to cycle the wheel of the flat wheel of the half tower, and the number of turns on the flat wheel is determined according to the part of the body on the sliding door of the lifting height.


上一篇:自動感應門安全性能因素有哪些?
下一篇:車庫門款式該如何設計好?
產品中心
聯係向日葵污视频下载