谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 行業新聞 >

車庫門固定式扭簧接頭工藝流程!

發布人:http://www.levels4life.com    發布時間:2020-03-26 14:44:03

  手動車庫門和自動車庫門的主要區別是沒有馬達。自動庫門主要分為:轉動盤車庫門和卷簾車庫門,當門較大時,不方便安裝在地麵門體處,車庫門起著方便、快捷的開啟作用。在現有的自動切庫門,是一種常見的轉板切庫門,切庫門配有減震彈簧平衡係統,其原則是扭轉彈簧平衡係統產生的扭矩和門的質量,扭轉彈簧平衡係統的幫助下實現上下運動。由於使門體處於“零重量”狀態,靠滑輪在軌道內運行,因此阻力小,能耗小,而且維修率低,耐磨性好。扭轉管通常安裝有兩個相互連接的扭轉彈簧,扭轉彈簧兩端分別安裝有固定彈簧接頭和旋轉彈簧接頭。

  The main difference between a manual garage door and an automatic garage door is that there is no motor. The automatic garage door is mainly divided into: rotary disc garage door and rolling shutter garage door. When the door is large, it is inconvenient to install on the ground door body, and the garage door plays a convenient and quick role in opening. In the existing automatic cutting door, it is a common rotating plate cutting door. The cutting door is equipped with a damping spring balance system. Its principle is the torque generated by the torsion spring balance system and the quality of the door. With the help of the torsion spring balance system, the up and down movement is realized. Because the door body is in the "zero weight" state and runs in the track by the pulley, the resistance is small, the energy consumption is small, and the maintenance rate is low, and the wear resistance is good. The torsion tube is usually equipped with two mutually connected torsion springs, both ends of which are respectively equipped with fixed spring joints and rotary spring joints.

  目前,車門的固定扭轉彈簧接頭采用鐵製件,重量大,使用壽命短,成本高,環境汙染嚴重。車庫門常用的固定扭轉彈簧接頭是由一個整體構成的。在接頭體下方的安裝體上嵌有扭力彈簧,然後將扭力彈簧接頭固定在扭力管上。雖然扭力彈簧聯合是重量輕和低成本,發現扭力彈簧的同心度關節扭力彈簧的兩端是可憐的安裝後,在長期使用和磨損程度高,導致使用壽命短。

20161214103489.jpg

  At present, the fixed torsion spring joint of the door is made of iron, which has the advantages of large weight, short service life, high cost and serious environmental pollution. The fixed torsion spring joint commonly used in garage door is composed of a whole. A torsion spring is embedded in the mounting body under the joint body, and then the torsion spring joint is fixed on the torsion pipe. Although the combination of torsion spring is light in weight and low in cost, it is found that the two ends of the concentricity joint torsion spring of torsion spring are pitifully installed after long-term use and high wear, resulting in short service life.

  車庫門開關固定扭力彈簧接頭,包括關節本體和本體位於關節底部的安裝,安裝後體位扭力彈簧,在連接器的身體的中心配備安裝槽,關節沿徑向的本體固定身體和第二固定身體,和固定的身體和第二固定體位於同一行的中心,第一固定身體的配備第一安裝孔,第二固定在身體配備第二安裝孔,安裝在身體上配備了第一個線程描述的第一線槽和槽相對於第二線槽,第一個線程之間的缺口槽和第二個槽。避免了扭轉管的抖動,有利於改善車庫門安裝後帶有固定扭轉彈簧接頭的同軸性,有效減少了磨損,提高了門的使用壽命。

  The fixed torsion spring joint of garage door switch includes the installation of joint body and body at the bottom of joint. After installation, the body position torsion spring is installed. The center of the body of the connector is equipped with an installation groove. The joint is fixed with the body along the radial direction and the second fixed body, and the fixed body and the second fixed body are located in the center of the same line. The first fixed body is equipped with a first installation hole, The second fixing is provided with a second mounting hole on the body which is provided with a first slot and a slot described by the first thread relative to the second slot, a notch slot and a second slot between the first thread. The utility model can avoid the shaking of the torsion tube, improve the coaxiality of the fixed torsion spring joint after the garage door is installed, effectively reduce the abrasion and improve the service life of the door.


上一篇:車庫門來回開關不嚴怎麽辦?
下一篇:如何安裝高效的快速卷簾門?
產品中心
聯係向日葵视频app下载ioses网站免费