谘詢熱線
-->
當前位置: 首頁 > 新聞中心 > 行業新聞 >

電動卷簾門的限位器該如何調節?

發布人:http://www.levels4life.com    發布時間:2020-06-10 14:14:22

電動卷簾門應有兩個限位開關。 一個是上限,另一個是下限。 限位開關應具有機械轉動杠杆,以控製開關的停止和啟動。
The electric roller shutter shall have two limit switches. One is the upper limit, the other is the lower limit. The limit switch shall have a mechanical turning lever to control the stop and start of the switch.
調整期間,應由兩個人操作。 一個人可以調節機械旋轉杆在頂部的位置,而另一個人可以控製卷簾門的上下位置來配合調節限位開關的位置。
During the adjustment, it should be operated by two people. One person can adjust the position of the mechanical rotary lever at the top, while the other person can control the up and down positions of the roller shutter door to coordinate with the position of the limit switch.
卷簾門極限調試方法:
Limit debugging method of rolling shutter door:
1.將限位器上的螺母卡旋轉到合適的角度以脫開塞子螺母,或鬆開限位器上的鎖緊螺釘。
1. Turn the nut clamp on the stopper to a proper angle to release the plug nut, or loosen the locking screw on the stopper.
2.將門打開到合適的位置後,旋轉限位器上的限位螺母使其壓住開門限位開關上的滾輪。 聽到“嘀嗒”聲後,將螺母卡卡入到相應的限位螺母中或是擰緊螺釘。
2. After opening the door to a proper position, turn the limit nut on the limit device to press it against the roller on the limit switch. After hearing the "ticking" sound, clip the nut into the corresponding limit nut or tighten the screw.
3.將門關閉到合適的位置後,轉動限位器上的限位螺母使其壓住關門限位開關上的滾輪。 聽到“嘀嗒”聲後,將螺母卡片卡入到相應插槽中的限位螺母中或擰緊螺釘。
3. After closing the door to a proper position, turn the limit nut on the limit device to press it against the roller on the limit switch. After hearing the "tick", clip the nut card into the limit nut in the corresponding slot or tighten the screw.
4.如果門的位置不合適,則可以再次將其調節到最佳位置。
4. If the position of the door is not suitable, it can be adjusted to the best position again.
卷閘門的設置要求規定:
The setting requirements of the rolling gate are as follows:
1.當掛鉤滑動到極限位置時,便抬起杠杆。 當按下限位開關時,電路將關閉,再合匣時,掛鉤才能下降。
1. When the hook slides to the limit position, lift the lever. When the limit switch is pressed, the circuit will be closed, and then the hook can be lowered when the box is closed.
2.在軌道的端頭(在操作限定的位置)安裝一個固定的限位擋板。 當塔式起重機運行到該位置時,限位擋板觸碰行程開關的扳把,切斷電源以控製行程。再合閘時,塔吊隻能以相反的方向運行。
2. Install a fixed stop plate at the end of the track (at the position limited by the operation). When the tower crane moves to this position, the limit baffle touches the handle of the travel switch to cut off the power supply to control the travel. When reclosing, the tower crane can only operate in the opposite direction.
3.在盤的中央安裝垂直移動的指針。 當改變振幅時,指針指示出在各種振幅下的額定起重量。 當動臂杆移動到上限和下限位置時,分別按下限位開關,切斷主控製電路,變幅電機停車,並達到限位的作用。
3. Install the vertically moving pointer in the center of the disk. When the amplitude is changed, the pointer indicates the rated lifting capacity under various amplitudes. When the boom moves to the upper and lower limit positions, press the limit switches respectively, cut off the main control circuit, stop the luffing motor, and achieve the function of limit.
上一篇:濟南卷簾門維修需要注意的幾個問題?
下一篇:濟南車庫門幾種風格選擇
產品中心
聯係向日葵视频色板app免费下载